thenewred 4w ago • 100%
Why can't they use the excess energy to make the train go again?
thenewred 2mo ago • 100%
What is this used for?
thenewred 2mo ago • 100%
Is there a bad taxidermy community?
thenewred 2mo ago • 96%
They were asking for a ride. She speaks Ukrainian. I'm guessing she wasn't bothered by it.
thenewred 2mo ago • 100%
I might have crossed my wires, it was probably just a forum post I misread. I happened to have new ceramic burrs so I went ahead and installed them.
I got closer to a perfect pull this morning after adjusting the right lever! Unfortunately I'm out of that coffee now so the process restarts with the next bag.
thenewred 2mo ago • 100%
New ceramic burrs.
I typically use light roast beans, apparently ceramic is better there.
Went through the hyperalignment procedure and got close but not perfect. Had to move on and get it back together at some point.
thenewred 2mo ago • 100%
Works the same, just inline. And this grinder has two
thenewred 2mo ago • 100%
I don't know about best, but these have been decent
Slurping Turtle (Easton)
Wild Ginger (Hilliard)
Aki Hana (Henderson)
Facepalm
thenewred 3mo ago • 100%
Me writing my resume in third person
thenewred 3mo ago • 95%
Is this comparing total number of visitors per year to inhabitants?
If so, it's a misleading graphic because visitors only stay for a week or two.
thenewred 3mo ago • 100%
A blessing! Free credit monitoring! All is well
thenewred 3mo ago • 87%
Free solo*
But with a harness full of gear for extra weight reasons
And gloves because less grip == good?
thenewred 4mo ago • 100%
Me, spending hours on Age of Empires 2 and loving it
thenewred 7mo ago • 100%
We water by soaking the plants in the tub, then letting them sit on towels before going back on the shelf. A bit tedious but only has to be done every 1-2 months.
thenewred 7mo ago • 100%
True with crimps, not as important with pinches, which is what this mug is
thenewred 7mo ago • 100%
This is how I did it with my old board. My new board has a jumper to toggle between powering via USB and not.
thenewred 8mo ago • 100%
When the only tool you have is a deep lifelong understanding of computational language, everything starts to look like a hypergraph.
Just learned about this. A long read, but really interesting.
thenewred 8mo ago • 99%
Cisco Webex.
You think teams or zoom are annoying? This is much worse. The worst part is with some default meeting settings, a loud chime would play every time someone joined. People kept this on for meetings of 300+ people, then they started talking over the beeps once "the popcorn slowed down."
Update to my previous post: https://lemmy.ca/post/7236274
I don't know why I even bother opening the settings app
Pretty happy with how this turned out, even months later 
https://www.mountainproject.com/v/105748478
It's wild how similar woodworking and 3d printing are. 1. Get a 3d printer 2. Print things for the 3d printer With woodworking 1. Get a table saw 2. Make things for the table saw Now I can mix and match Model: https://www.printables.com/model/205258-featherboard-with-replaceable-heads-m6
Designed this storage solution for belts https://www.printables.com/model/519768-belt-organizer-hanger-6-or-8-belts   
Had minimal clearance between these overhead shelves and the garage door, and the perfect light spacing was a few inches away from the cross bars. So I designed these snap fit brackets to offset the lights inline. The lights make a huge difference, much more pleasant to work in the garage. What I learned: * there is some sag because the screws aren't at the top of the bracket. I would add a tab that protrudes on the side so I could add a screw higher. * the screw face split on layer lines on a few of these. Still works but not perfect, so I would make the screw face thicker.   Also printed cable management clips 
Made entirely from 1x2 pine. Ripped into thirds for the shelf slats. Pocket holes. Glue. Brads and glue for the shelf slats.       
