ostsjoe 1d ago • 100%
Try booting something different on proxmox like an ubuntu live desktop, just to make sure networking is working there. Seems like haos can't talk to the Internet.
ostsjoe 3w ago • 100%
Yeah I'm not defending it, just doubt it was intentional, hopefully they sort their shit out. The fact that it's a GoDaddy project bouncing you isn't a great sign of that.
ostsjoe 3w ago • 100%
ostsjoe 3w ago • 100%
Probably just over zealous ddos protection. It's often a balance of a few false positives in order to keep the site online.
ostsjoe 2mo ago • 100%
If a controller is still connected (Bluetooth?) it may be a controller order issue, you can try reordering them.
ostsjoe 9mo ago • 100%
No, the browser would still send YouTube.com as the host header. While yewtu.be could be configured to allow this to work, the TLS cert would not and the browser would get upset.
ostsjoe 9mo ago • 100%
Also the alternator absolutely takes more power from the engine in proportion to how much energy it's putting out.
ostsjoe 12mo ago • 100%
O
ostsjoe 12mo ago • 83%
Jellyfin is very conveniently packaged in docker, so while it may seem daunting, I highly recommend at least trying that route.
Running an nfs mount, docker or not, should be perfectly fine. Jellyfin just uses normal storage so won't care if it's nfs. No real special considerations with proxmox either, especially without worrying about a dedicated GPU. Just spin up a Debian guest and go.
ostsjoe 1y ago • 100%
Fortunately that's not how it works when you have all the access points controlled centrally, like with unifi. Yes there is limited frequency space, but this is much less of an issue on 5ghz. There will also only be one ssid, and handoff between access points is pretty seamless.
3-4 is probably overkill, but the attenuation situation sounded pretty dire. I run two in my house for redundancy mostly, just standard American stud and drywall construction.
ostsjoe 1y ago • 100%
If you have the ability to easily add wires, I would go with a system that allows you to wire everything together, rather than depending on a purely wifi mesh. Personally I'm running unifi ceiling mounted access points for this. They run on power over Ethernet, so you just need to get one cable to each. You can control them with their free software controller if you are into that, or something like their dream router.
Run 3-4 of those access points placed throughout the house and you'll never have a weak signal again.
ostsjoe 1y ago • 100%
Why does this only work in Hondas? What about this cares about the car?
ostsjoe 1y ago • 100%
Sand, sand, and sand some more. When you think you are done sanding, sand some more.
ostsjoe 1y ago • 100%
I used the paper plans from Chesapeake light craft, and was able to source most of the supplies locally. It's built from marine grade plywood, 4 mil thick, traced off the paper plans and cut out with a jig saw. It's then "stitched" together with copper wire and "glued" together with epoxy resin and the whole thing covered in fiberglass. That's an over simplification of the process, but it's really not too bad, just time consuming. Took me close to 6 months of nights and weekends off and on, probably about $800 all in.
Kayak is a clc shearwater sport that I built in my basement.
ostsjoe 1y ago • 100%
If you have a free pcie 4x or higher slot, you can throw in a cheap card to adapt to m.2 nvme, like 12 bucks. I'm running one in my older hp desktop that doesn't have m.2 and it's been working great.
ostsjoe 1y ago • 100%
For a quick test you could set it to 777, if that fixes it, check which user new files are being assigned to, adjust permissions back down accordingly.
ostsjoe 1y ago • 100%
We need more info on your permissions. 755 would mean anyone can read files there, but only the owner can write. If the owner isn't the same user that mediawiki is running as, then uploads won't work.
ostsjoe 1y ago • 100%
I have no way to test this with the equipment I have, but what about opnsense on an x86-64 box and throw an sfp+ pcie card in there. You could then in theory turn off auto negotiation and set it to 2.5g. Has anyone out there tried this?
I've been running opnsense with my CenturyLink 1g setup, though I'm still using their ont to convert to copper, and been very happy with it.